SITEMAP
HIGH CARBON STEEL
HARDENED AND TEMPERED STRIP STEEL FOR HIGH CARBON STEEL
Steel that carbon content of 0.5 percent or higher carbon consider as a High carbon steel. High carbon steel include hardness and resistance to wear.
And also High carbon steel is less formable and machinable than low-carbon steel.
High carbon steel is used in cutting tools and garden tools. Reason is high carbon steel has ability to keep a sharp edge.
And also High carbon steel is less formable and machinable than low-carbon steel.
High carbon steel is used in cutting tools and garden tools. Reason is high carbon steel has ability to keep a sharp edge.
Specification
| THICKNESS | 0.1 ~ 4.0 mm |
|---|---|
| WIDTH | 5.0 - 450 mm |
| HARDNESS | HV 300 ~ 600 |
| STRUCTURE | Bainite, Tempered Martensite |
| HARDNESS TOLERANCE | ± HV 20 (Special ± HV 10) |
| STRAIGHTNESS | Max 0.5mm / 1,000 mm length |
| CROSS CAMBER | Max 3μm / mm Width (Special Max 1μm/ mm Width) |
| SURFACE COLOR | Unpolished blue, Bright, Polished blue, Polished white, Polished yellow |
| EDGE FINISH | Slit edge, Deburred edge, Round edge, chamfered edge, Square edge |
| INNER DIAMTER | MIN. 300 ~ 600mm |
| OUTER DIAMETER | MAX. 1,800mm |
Application
Strip Steel for Automobile Industry
Specification
| THICKNESS | 0.1 ~ 4.0 mm |
|---|---|
| WIDTH | 5.0 - 450 mm |
| HARDNESS | HV 300 ~ 600 |
| STRUCTURE | Bainite, Tempered Martensite |
| HARDNESS TOLERANCE | ± HV 20 (Special ± HV 10) |
| STRAIGHTNESS | Max 0.5mm / 1,000 mm length |
| CROSS CAMBER | Max 3μm / mm Width (Special Max 1μm/ mm Width) |
| SURFACE COLOR | Unpolished blue, Bright, Polished blue, Polished white, Polished yellow |
| EDGE FINISH | Slit edge, Deburred edge, Round edge, chamfered edge, Square edge |
| INNER DIAMTER | MIN. 300 ~ 600mm |
| OUTER DIAMETER | MAX. 1,800mm |
Application
Strip Steel for Saw Blade/Others
Specification
| THICKNESS | 0.1 ~ 4.0 mm |
|---|---|
| WIDTH | 5.0 - 450 mm |
| HARDNESS | HV 300 ~ 600 |
| STRUCTURE | Bainite, Tempered Martensite |
| HARDNESS TOLERANCE | ± HV 20 (Special ± HV 10) |
| STRAIGHTNESS | Max 0.5mm / 1,000 mm length |
| CROSS CAMBER | Max 3μm / mm Width (Special Max 1μm/ mm Width) |
| SURFACE COLOR | Unpolished blue, Bright, Polished blue, Polished white, Polished yellow |
| EDGE FINISH | Slit edge, Deburred edge, Round edge, chamfered edge, Square edge |
| INNER DIAMTER | MIN. 300 ~ 600mm |
| OUTER DIAMETER | MAX. 1,800mm |
Microstucture
- Fully spheroidized pin-point carbides
- Free of carbide network or lamellar pearlite and free of carbide alignment, uniformly distributed in a ferrite matrix.
- Carbide size is less than 1 micron diameter, maximum carbide is not exceed 3 microns, carbide spacing shall not exceed 4microns.
Application
Shaving Strip Steel
Edge finishing the right edge for every application
- All kind of edge customer requirement, we can shave it precisely in the strip edge-deburred, round, chamfered, square, bevel shaved, bevel shaved +High frequency etc.
- On request we can meet edge geometry of our strip steels exactly, so that customer uses it in their application, such as band saw, steel rule, rotary rule, springs etc.
- We can also use our shaving machines to prepare the edge for final finishing on customer requirement.
| FINISH TYPE | DEFINITION | APPLICATION | IMAGE |
|---|---|---|---|
| Slit edge | sharp edged with slitting burrs left on | left spring |  |
| Deburred edge | slit edges from which burrs have been removed |
left spring |  |
| Round edge | edged rounded | power spring |  |
| Chamfered edge | square edge with round corner | saws and blades |  |
| Square edge | sharp-cornered square edges | band saws |  |
| Bevel shaved edge | sharp-bevel | rotary rule |  |
| Bevel shaved edge + High frequency |
sharp-bevel with high frequency of edge | rotary rule |  |
Available dimesion
Specification
| THICKNESS | 0.1 ~ 4.0 mm |
|---|---|
| WIDTH | 5.0 - 450 mm |
| HARDNESS | HV 300 ~ 600 |
| STRUCTURE | Bainite, Tempered Martensite |
| HARDNESS TOLERANCE | ± HV 20 (Special ± HV 10) |
| STRAIGHTNESS | Max 0.5mm / 1,000 mm length |
| CROSS CAMBER | Max 3㎛ / mm Width (Special Max 1㎛/ mm Width) |
| SURFACE COLOR | Unpolished blue, Bright, Polished blue, Polished white, Polished yellow |
| EDGE FINISH | Slit edge, Deburred edge, Round edge, chamfered edge, Square edge |
| INNER DIAMTER | MIN. 300 ~ 600mm |
| OUTER DIAMETER | MAX. 1,800mm |
Unit Cutting Strip Steel
Specification
| THICKNESS | 0.5 ~ 2.0 mm |
|---|---|
| WIDTH | 10 ~ 100 mm |
| STRAIGHTNESS | Max 0.5mm / 1,000mm length |
| CROSS CHAMBER | Max. 3㎛ / mm Width (Special Max. lum / mm Width) |
Specification for Oscillating
| THICKNESS | ~ 2.0 mm |
|---|---|
| WIDTH | ~ 70 mm |
Technical information (Tolerance of form)
Packing
Specification
| IN DIA METER | 400 ~ 510 mm |
|---|---|
| OUT DIA METER(MAX) | ~ 2,000 mm |
| WEIGHT (MAX) | ~ 2,000 kg |
| REMARK | In coil, Wrapped |
