SITEMAP
HARDENED AND TEMPERED STRIP STEEL
HARDENED AND TEMPERED STRIP STEEL
Hardened and Tempered Strip Steel is the final result of a high carbon steel which has done the heat treatment.
After heat treatment there is Tempering and it will make Hardened and Tempered strip steel toughen and improve the overall of the steel.
Hardened and Tempered Strip Steel is used for producing a saw, automobile parts, gardening, scraper tools, spring, brush cutter blade, wiper … etc.
Hardened and Tempered strip steel is a steel coil that has been subjected to a series of heating and cooling system.
For Hardened and Tempered strip steel production methods are unique, extensively adapted.
After heat treatment there is Tempering and it will make Hardened and Tempered strip steel toughen and improve the overall of the steel.
Hardened and Tempered Strip Steel is used for producing a saw, automobile parts, gardening, scraper tools, spring, brush cutter blade, wiper … etc.
Hardened and Tempered strip steel is a steel coil that has been subjected to a series of heating and cooling system.
For Hardened and Tempered strip steel production methods are unique, extensively adapted.
Specification
| THICKNESS | 0.1 ~ 4.0 mm |
|---|---|
| WIDTH | 5.0 - 450 mm |
| HARDNESS | HV 300 ~ 600 |
| STRUCTURE | Bainite, Tempered Martensite |
| HARDNESS TOLERANCE | ± HV 20 (Special ± HV 10) |
| STRAIGHTNESS | Max 0.5mm / 1,000 mm length |
| CROSS CAMBER | Max 3μm / mm Width (Special Max 1μm/ mm Width) |
| SURFACE COLOR | Unpolished blue, Bright, Polished blue, Polished white, Polished yellow |
| EDGE FINISH | Slit edge, Deburred edge, Round edge, chamfered edge, Square edge |
| INNER DIAMTER | MIN. 300 ~ 600mm |
| OUTER DIAMETER | MAX. 1,800mm |
Application
Strip Steel for Automobile Industry
Specification
| THICKNESS | 0.1 ~ 4.0 mm |
|---|---|
| WIDTH | 5.0 - 450 mm |
| HARDNESS | HV 300 ~ 600 |
| STRUCTURE | Bainite, Tempered Martensite |
| HARDNESS TOLERANCE | ± HV 20 (Special ± HV 10) |
| STRAIGHTNESS | Max 0.5mm / 1,000 mm length |
| CROSS CAMBER | Max 3μm / mm Width (Special Max 1μm/ mm Width) |
| SURFACE COLOR | Unpolished blue, Bright, Polished blue, Polished white, Polished yellow |
| EDGE FINISH | Slit edge, Deburred edge, Round edge, chamfered edge, Square edge |
| INNER DIAMTER | MIN. 300 ~ 600mm |
| OUTER DIAMETER | MAX. 1,800mm |
Application
Strip Steel for Saw Blade/Others
Specification
| THICKNESS | 0.1 ~ 4.0 mm |
|---|---|
| WIDTH | 5.0 - 450 mm |
| HARDNESS | HV 300 ~ 600 |
| STRUCTURE | Bainite, Tempered Martensite |
| HARDNESS TOLERANCE | ± HV 20 (Special ± HV 10) |
| STRAIGHTNESS | Max 0.5mm / 1,000 mm length |
| CROSS CAMBER | Max 3μm / mm Width (Special Max 1μm/ mm Width) |
| SURFACE COLOR | Unpolished blue, Bright, Polished blue, Polished white, Polished yellow |
| EDGE FINISH | Slit edge, Deburred edge, Round edge, chamfered edge, Square edge |
| INNER DIAMTER | MIN. 300 ~ 600mm |
| OUTER DIAMETER | MAX. 1,800mm |
Microstucture
- Fully spheroidized pin-point carbides
- Free of carbide network or lamellar pearlite and free of carbide alignment, uniformly distributed in a ferrite matrix.
- Carbide size is less than 1 micron diameter, maximum carbide is not exceed 3 microns, carbide spacing shall not exceed 4microns.
Application
Shaving Strip Steel
Edge finishing the right edge for every application
- All kind of edge customer requirement, we can shave it precisely in the strip edge-deburred, round, chamfered, square, bevel shaved, bevel shaved +High frequency etc.
- On request we can meet edge geometry of our strip steels exactly, so that customer uses it in their application, such as band saw, steel rule, rotary rule, springs etc.
- We can also use our shaving machines to prepare the edge for final finishing on customer requirement.
| FINISH TYPE | DEFINITION | APPLICATION | IMAGE |
|---|---|---|---|
| Slit edge | sharp edged with slitting burrs left on | left spring |  |
| Deburred edge | slit edges from which burrs have been removed |
left spring |  |
| Round edge | edged rounded | power spring |  |
| Chamfered edge | square edge with round corner | saws and blades |  |
| Square edge | sharp-cornered square edges | band saws |  |
| Bevel shaved edge | sharp-bevel | rotary rule |  |
| Bevel shaved edge + High frequency |
sharp-bevel with high frequency of edge | rotary rule |  |
Available dimesion
Specification
| THICKNESS | 0.1 ~ 4.0 mm |
|---|---|
| WIDTH | 5.0 - 450 mm |
| HARDNESS | HV 300 ~ 600 |
| STRUCTURE | Bainite, Tempered Martensite |
| HARDNESS TOLERANCE | ± HV 20 (Special ± HV 10) |
| STRAIGHTNESS | Max 0.5mm / 1,000 mm length |
| CROSS CAMBER | Max 3㎛ / mm Width (Special Max 1㎛/ mm Width) |
| SURFACE COLOR | Unpolished blue, Bright, Polished blue, Polished white, Polished yellow |
| EDGE FINISH | Slit edge, Deburred edge, Round edge, chamfered edge, Square edge |
| INNER DIAMTER | MIN. 300 ~ 600mm |
| OUTER DIAMETER | MAX. 1,800mm |
Unit Cutting Strip Steel
Specification
| THICKNESS | 0.5 ~ 2.0 mm |
|---|---|
| WIDTH | 10 ~ 100 mm |
| STRAIGHTNESS | Max 0.5mm / 1,000mm length |
| CROSS CHAMBER | Max. 3㎛ / mm Width (Special Max. lum / mm Width) |
Specification for Oscillating
| THICKNESS | ~ 2.0 mm |
|---|---|
| WIDTH | ~ 70 mm |
Technical information (Tolerance of form)
Packing
Specification
| IN DIA METER | 400 ~ 510 mm |
|---|---|
| OUT DIA METER(MAX) | ~ 2,000 mm |
| WEIGHT (MAX) | ~ 2,000 kg |
| REMARK | In coil, Wrapped |
